Inclinator VL
 Inclinator’s VL is the workhorse in the industry. At first glance, it’s very similar to other wheelchair lifts. But take into account Inclinator’s reputation for having the most reliable products and best technical and customer support, plus a 2-year parts warranty, and you’ve got the best value for a steel vertical wheelchair lift.
Key Advantages
- Guiding system uses our monorail “C” channel with trolley and safeties.
- Tower support is a unique steel ladder for support and rigidity.
- Lifting mechanism (ACME screw) is secured at the top with a high quality, self-centering bearing which also supports the driven pulley.
- Motor, pulleys, broken belt safety switches and controller are located at the top to make servicing easier.
- Access is gained through a removable access panel located toward the top of the tower front panel.
- Side plates house the dual broken screw safety (unique to lifts of this type).
- Failure of the screw, nut or other part of the lifting mech- anism, which should cause a decrease in tension on sens- ing plate, will engage the safety dogs which hold the plat- form, and disconnect power to the motor.
- Removable tower base legs.
- Tower is approximately 40" wide with the legs in place. When removed, the tower is only 24" wide, allowing the unit to pass through a normal doorway.
- In addition to strut supports, eight-, ten-, and twelve-foot units have brackets for attaching the tower to a structure.
- Optional outdoor package.
- 2-Year warranty on all parts.
 Key Features
- Adaptable for indoor and outdoor usage
- Easy installation and service
- Emergency stop, alarm and keyswitch
- 750 lb. capacity
- Standard 12 sq. ft. platform (15 sq. ft. option)
- Up to 12' travel distance
- Heavy gauge sheet steel is used to enclose the tower assembly
- Screw support (to reduce screw oscillation) is provided on units with longer travels
- 16 gauge carbon steel with weather resistant coating
- 16 gauge carbon steel ramp with powder coating
Specifications
Standard Equipment
- Design: Designed to meet or exceed the require- ments of ANSI A18.1 Capacity – 750 lbs.
- Speed: 10FPM Travel Distance – Up to 12 ft.
- Motor: 1 HP, 1725 RPM, 120 VAC, 60 HZ, 15 AMPS, single phase, instant reversing. Conveniently located at the top of the tower. 30 AMP designated service.
- Drive: ACME screw with self-centering driven pulley, three V-Belts with broken belt safety switch. Manual raise and lowering.
- Guiding Means: Monorail “C” channel with captivated trolley and safeties.
- Finish: Baked-on powder finish in beige, standard.
- Dual Safety Dogs: Secures the platform to the guiding rails if there should be a failure of the lifting means.
- Limit Switch: Up and down limit switches with a final limit to disconnect main power in the event of an overrun.
- Control: Up/down paddle switch on platform and at landings. Keyswitch, alarm, and emer- gency stop switch on units for public installations. 24 VAC.
- Tower: 16 ga. auto steel with weather resistant coating. Removable base legs make handling and installation easier. Upper service panel removable for quick assess to motor, controller. Spliced tower skirt on 10 ft. and 12 ft. models.
- Platform: 12 sq. ft. (15 sq. ft. optional). 42" high sides. Handrail on each long side. Platform floor and ramp have non-skid surfaces.
- Platform Safety Diaphragm: Suspended from bottom of platform. Stops downward motion of the unit if an obstruction is encountered.
- Shipping: Unit is shipped partially assembled and pre-wired.
- Testing: All units are inspected and run with capacity load before leaving the factory.
Optional Equipment
- Platform Gate: 42" high with interlock.
- Landing Gate: 42" high with interlock.
- Auto Fold Ramp: On platform, which locks in the up posi- tion to act as a guard.
- Stationary Ramp: To be used at the lower landing if no pit is provided.
- Ninety Degree Exits: Platform can have entry from one or two sides.
- Plexiglas Enclosure: With flush doors and GAL interlocks.
|
